PepCalcs

    TB-500 Reconstitution Calculator

    Dial in your TB-500 concentration and dose volume in seconds.

    Open the calculator

    Pre-filled with TB-500 defaults — adjust vial size, water volume, and dose to your protocol.

    About the TB-500 Reconstitution Calculator

    TB-500, a synthetic fragment related to Thymosin Beta-4, is typically supplied as a 2 mg, 5 mg, or 10 mg lyophilized vial and reconstituted with bacteriostatic water. Because research protocols usually call for weekly or twice-weekly loading doses of 2–5 mg followed by lower maintenance doses, choosing the right reconstitution volume matters — you want a concentration that draws in a reasonable number of insulin units per dose without wasting vial volume.

    Enter your vial strength, the bacteriostatic water you'll add, and your desired dose. The calculator returns the mg/mL concentration, the mL to draw, and the equivalent insulin units, and can also suggest an optimal reconstitution volume that lands each dose on a whole-unit mark.

    A common example: a 5 mg vial reconstituted with 2 mL of bacteriostatic water gives 2.5 mg/mL. A 2.5 mg loading dose is then 1 mL (100 units on a U-100 syringe), and a 1 mg maintenance dose is 0.4 mL (40 units).

    Quick reference

    Typical vial sizes
    2 mg · 5 mg · 10 mg
    Typical research dose range
    2–5 mg loading, then 1–2 mg weekly maintenance

    How to prepare TB-500

    1. Draw the intended volume of bacteriostatic water into a sterile syringe.
    2. Slowly inject the water down the inside wall of the TB-500 vial — never directly onto the lyophilized powder.
    3. Gently swirl (do not shake) until the powder is fully dissolved and the solution is clear.
    4. Store the reconstituted vial refrigerated at 2–8°C and use within the peptide's stability window.
    5. Use the concentration and dose volume calculated above to draw each research dose into an insulin syringe.

    Frequently asked questions

    How do I reconstitute TB-500?

    Add bacteriostatic water to the TB-500 vial using the volume the calculator recommends for your desired concentration. Slowly inject the water down the side of the vial, swirl gently, and store the vial refrigerated.

    What bacteriostatic water volume should I use for TB-500?

    Common choices are 1 mL, 2 mL, or 3 mL of bacteriostatic water. The right volume depends on your vial strength and target dose — use the calculator above to get a concentration that lets you draw your dose in whole insulin units.

    What is a typical research dose range for TB-500?

    Reported research dose ranges for TB-500 are 2–5 mg loading doses followed by 1–2 mg weekly. Always verify against current literature — this tool is for research reference only, not medical advice.

    How long is TB-500 stable after reconstitution?

    Once reconstituted with bacteriostatic water and stored refrigerated (2–8°C), most peptides remain stable for roughly 28–30 days. Check the specific stability data for TB-500 for your batch.

    Can I use this TB-500 calculator with any insulin syringe?

    Yes. The calculator supports U-100 syringes in 30, 50, and 100-unit capacities and shows both the mL dose volume and the equivalent insulin units for whichever syringe you choose.

    Read the full TB-500 profile

    Related calculators

    免责声明:仅供研究与教育用途

    本网站提供的信息仅供研究与教育用途,不用于人体的医疗处置、诊断或治疗。本网站不提供医疗建议,站内任何内容均不应视为专业医疗建议、诊断或治疗的替代。如对任何医疗状况或治疗有疑问,请务必咨询具备资质的医疗专业人员。切勿因本网站的信息而忽视专业医疗建议或延误就医。所提供的计算结果、剂量信息和肽类数据仅供参考与研究之用。将这些信息用于实际治疗或给药,风险由您自行承担。本网站运营方对基于此处信息所采取的任何行为不承担任何责任。